Anthem Statement D2v

D2v Technical Specifications

VIDEO SWITCHING

Bandwidth from input to output jack (bypass mode for component video)

Composite and S-Video
Component:	Y
	Pr
	Pb

70 MHz

110 MHz

90 MHz

80 MHz

All analog video inputs and outputs are 75 Ω, 1.5 Vp-p.

ANALOG AUDIO

Input Impedance

20 kΩ

Output Impedance
	Main-RCA
	XLR
	Zones 2/3 and Record

300 Ω

600 Ω

51 Ω

Rated Input

2.0 Vrms

Maximum Input

5.3 Vrms

Minimum Load

5 kΩ

Rated Output (100 kΩ load)

2.0 Vrms

Maximum Output
	RCA
	XLR

6.3 Vrms

12.6 Vrms

Headphone Output

100 mW into 32 Ω at 0.2% THD+N

Volume Control Range
	Main
	Zone 2/3 and Headphone

- 95.5 dB to +31.5 dB (in 0.5 dB increments)

- 62.5 dB to +10.0 dB (in 1.25 dB increments)

Crosstalk (at 1 kHz)

82 dB between channels; 86 dB between inputs

XLR Pin Configuration

Pin 1: Ground, Pin 2: Positive, Pin 3: Negative

DIGITAL AUDIO

Crossover
	High-Pass Slope (small speaker setting)
	Low-Pass Slope (subwoofer)
	Frequency (adjustable)

12 dB/octave (2nd order)

24 dB/octave (4th order)

25 Hz to 160 Hz (in 5 Hz increments)

Tone Control
	Fliter Type
	Range
	Bass Turnover Frequency
	Treble Turnover Frequency

Shelf

+/- 12 dB

200 Hz

2 kHz

Analog-to-Digital Conversion S/N Ratio (at digital Rec output) (IEC-A Filter)

100 dB

All digital audio inputs and outputs comply with HDMI, S/PDIF or AES/EBU standards. Sample rate converter output is 24 bit/192 kHz regardless of input.

MAIN PATH (RCA and XLR Outputs)

Frequency Response and Bandwidth
	Analog Direct Inputs
	Analog-DSP Inputs at 24/96
	Digital Inputs at 24/96

10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 130 kHz (+0 -3 dB)

10 Hz to 20 kHz (+0 -0.3 dB), 2 Hz to 44.1 kHz (+0 -3 dB)

10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 45 kHz (+0 -3 dB)

THD+N (at Rated Input and Output)
	Analog Direct Inputs
	Analog-DSP Inputs at 24/48 or 24/96
	Digital Inputs at 24/48 or 24/96

0.006% (80 kHz BW)

0.004% (AES17 Filter)

IMD (CCIF at 15 kHz and 16 kHz)
	Analog Direct Inputs
	Analog-DSP Inputs at 24/48
	Digital Inputs at 24/48 or 24/96

<0.001%

0.001%

S/N Ratio (ref. 2.0 Vrms, IEC-A Filter)
	Analog Direct Inputs
	Analog-DSP Inputs at 24/48 or 24/96
	Digital Inputs at 24/48 or 24/96

107 dB

101 dB

104 dB

ZONE 2 and ZONE 3 PATHS
Frequency Response and Bandwidth	20 Hz to 20 kHz (+0 -0.1 dB), 3 Hz to 140 kHz (+0 -3 dB)
THD+N (at Rated Input and Output)	0.06% (80 kHz BW)
IMD (CCIF at 15 kHz and 16 kHz)	0.06%
S/N Ratio (ref. 2.0 Vrms, IEC-A Filter)	97 dB

FM TUNER

Sensitivity
	50 dB S/N
	IHF

13 dBµ typical, 25 dBµ max.

10 dBµ typical, 20 dBµ max.

S/N Ratio
	Mono
	Stereo

75 dB typical, 65 dB min.

69 dB typical, 60 dB min.

Distortion
	Mono
	Stereo

0.2% typical, 1.0% max.

0.3% typical, 1.5% max.

Stereo Separation

40 dB typical, 25 dB min.

Alternate Channel Selectivity (+/- 400 kHz)

70 dB typical, 60 dB min.

Frequency Response

25 Hz to 15 kHz (+0 -2 dB)

AM TUNER
Sensitivity (20 dB S/N)	49 dBµ typical, 56 dBµ max.
S/N Ratio	50 dB typical, 43 dB min.
Distortion	0.7% typical, 2.0% max.
One-Signal Selectivity (+/- 10 kHz)	24 dB typical, 18 dB min.

CONTROL

Infra Red
	Carrier Frequency
	Maximum 12 V Supply Current
	Maximum Emitter Current

38 kHz

150 mA

60 mA per output

RS-232 Interface
	Connection
	Pinout (D2v side)
	Baud Rate
	Configuration

DB-9F, straight-wired

Pin 2: Tx, Pin 3: Rx, Pin 5: Ground

1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

8 data bits, 1 stop bit, no parity bits, flow control
(RTS/CTS, none)

Trigger Outputs
	Polarity
	Maximum Current at 12 VDC
	Sequential Delay

tip positive, sleeve ground

300 mA between all three triggers

250 ms

POWER REQUIREMENT
Consumption	Maximum 170 W

DIMENSIONS

Height

5-7/8 inches (14.9 cm) including feet;
rack-mounting: 3 rack units without feet

Width
	Standard version
	Rack-Mount version
	No-Handle version

19-1/4 inches (49 cm)

19 inches (48.3 cm)

17-1/4 inches (43.8 cm)

Depth

15-1/4 inches (38.7 cm)

Weight (unpacked)

27 lb (12.3 kg)

AVAILABLE FINISH

Black

:: TOP ::